Dresser Makeover with Fabric

I've had a little project brewing in my mind for a long time... It's one of those projects when I just needed to find the right piece of furniture and the time to tackle it.  Over the years, I've seen some beautiful furniture makeovers by applying fabric directly to drawer fronts, etc and after seeing another dresser with linen applied to the drawer fronts on my trip to High Point Market, I knew I just had to try out the technique...

Sometimes tackling a new project or technique just doesn't turn out like how I pictured it would be and I'm happy to announce that it was way easier than I thought and I'm really thrilled at the results!  Since I was sort of winging this project, I didn't take pictures as I went along for a tutorial, but the steps are pretty clear-cut and I'll share the process.  You'll need the following:

• Dresser, sideboard, or other piece of furniture (preferably with flat-front drawers or panels)
• Fabric (I used a thick, linen-type fabric - outdoor fabric would work well too)
• Mod Podge (Matte) & small foam brush
• Razor blade (with new, sharp blade)
• Cutting mat or cutting surface
• Fine-grit sandpaper (I used 320)
• Desired Paint, topcoat 

Prep the piece as you normally would for painting (sand, clean, etc), paint and topcoat (wax) the frame and anywhere else that you are not going to cover with the fabric.  I used Annie Sloan Chalk Paint in Old White for the frame as it coordinated with the fabric (purchased several years ago) and knobs (from Hobby Lobby) I'd already selected.

To apply the fabric to the drawer fronts, you'll first need to measure and cut the fabric for each drawer.  It helps to add a good 1/4'' to 1/2'' excess around drawers, which are later trimmed.  With a small foam brush, apply a nice even coat of Mod Podge to the drawer fronts, attach the fabric panels and smooth them down all the way to the corners.

The trickiest part of the process is to get clean, smooth fabric edges on the drawers.  Mod Podge dries very quickly and after the fabric is initially adhered to the drawer, flip the drawer over onto a cutting mat and trim the excess fabric with a razor blade.  It helps to use the sharpest blade possible...the fabric was catching on the first drawer until I changed out the blade and it made a world of difference.

After trimming and cleaning up the edges of the fabric, apply the Mod Podge on top of the fabric and around all the edges.  It's important to apply liberally around the edges to keep the fabric from lifting and any fraying from happening.  Remember that Mod Podge looks white when it is applied, but dries clear.  After the first coat dries, repeat...I only needed two coats for this project.  At this point, the edges are going to feel a bit rough and the drawer fronts far from smooth.  Simply take the fine-grit sandpaper or sanding block and smooth out all the edges and drawer fronts...it worked wonders!  The matte Mod Podge leaves a nice, smooth finish that is easy to clean.
I applied the fabric to the drawer fronts before I painted the sides and top edges of the drawers, but the order isn't important.  I did find that waxing along the paint edges afterward made the fabric/paint edge even smoother.

To add the drawer hardware after the fabric covered up the pre-drilled holes, I simply poked a pencil through the hole from the inside of the drawer to mark where I needed cut the fabric with the razor blade.  You don't need a to cut much... Just enough for the screw on the back of the knob to fit through.

  

As I mentioned, it was a fairly easy project that can lead to endless possibilities of fabric and paint combinations!  I think you'll be seeing some more of these from me in the future :)

Kristen

Note:  This is not a sponsored post...all opinions about any products mentioned are my own.

Sharing here:
Coastal Charm
Cedar Hill Ranch
Uncommon Slice of Suburbia
Home Stories A to Z
Savvy Southern Style
Common Ground
French Country Cottage
Miss Mustard Seed
Home Stories A to Z